Before you can mount a TV on a wall, you need to know where the studs are. Drywall screws have roughly 10x less pull-out strength than screws going into wood studs, so hitting the studs is non-negotiable for any permanent wall mount. Here are five methods, from most accurate to most accessible, that our technicians use and recommend.

What you're looking for: In standard US homes, studs are 2×4 or 2×6 lumber running vertically inside walls, spaced 16 inches on center (or 24" in older homes). Your TV mount needs at least 2 screws in solid wood studs, spaced apart by at least the width of the bracket's mounting holes.

Method 1: Electronic Stud Finder (Most Accurate)

Most Reliable Works on Drywall $15–$60 Tool Cost

An electronic stud finder detects changes in wall density by measuring capacitance, it reads differently over hollow drywall versus the solid backing of a stud. Mid-range models (Franklin ProSensor T6, Zircon MultiScanner i520) also detect live electrical wires, which is a valuable safety check before drilling.

Correct Technique (Most People Do This Wrong)

1

Start away from studs

Place the stud finder at least 6" from any suspected stud. Hold it flat against the wall and press the calibration button. It calibrates to the drywall density, if you start on top of a stud, it calibrates to stud density and reads everything as hollow.

2

Scan slowly left to right

Slide the tool slowly in one direction without lifting it. Wait for the alert (beep or indicator light). Mark the wall lightly with a pencil at the first edge detection.

3

Scan back from the other side

Scan the same area from right to left and mark the second edge detection. The stud center is exactly halfway between your two marks.

4

Confirm before drilling

Drive a thin finish nail at your center mark. If you feel solid resistance after the nail passes through drywall (about 1/2"), you've hit the stud. If the nail goes in easily all the way, you've missed, shift 1/2" and try again.

Method 2: Rare-Earth Magnet (Free, Highly Accurate)

Free Method Works on Plaster Too Requires Patience

Drywall is attached to studs with drywall screws or nails, typically placed every 12–16 inches vertically. A strong rare-earth magnet (neodymium, the type found in old hard drives) will noticeably pull toward these fasteners. This method works where electronic stud finders often fail: plaster walls, walls with inconsistent density, and walls with aluminum foil insulation backing.

How to Do It

  1. Tie a piece of dental floss or thin string around the magnet
  2. Dangle the magnet against the wall and slowly drag it horizontally
  3. When it clings or pulls strongly, you've found a drywall screw
  4. Mark that spot, the stud center is within 3/4" of the screw
  5. Scan 12–16 inches higher or lower to find another screw in the same stud, confirming the vertical line

Pro tip: This is the method our technicians use for plaster walls and for confirming stud finder readings in tricky walls. A neodymium magnet costs about $3 on Amazon and is more reliable than many $20 stud finders.

Method 3: Outlet-Based Measurement

No Tools Needed Code-Based Accuracy

Electrical outlet and switch boxes are code-required to be attached to the side of a stud. This gives you a known stud location anywhere you have an outlet. By NEC code, the box nailing flange is 3/4" from the stud face, so the stud is immediately adjacent to the outlet box.

Measurement Procedure

  1. Locate any outlet or light switch on the wall where you plan to mount
  2. Remove the cover plate and note which side the box attaches to the stud (usually right side, though this varies)
  3. Measure 3/4" from that side of the box, that's the stud face; center it and you have the stud center
  4. From this known stud, measure 16" horizontally toward your desired mounting location
  5. That 16" interval puts you at the next stud center

This method is most reliable in newer construction where stud spacing is consistent. In homes built before 1950, stud spacing can be inconsistent, confirm with a magnet or stud finder after measuring.

Skip the guesswork: our techs use thermal imaging

Our professional TV mounting service includes stud location as part of every installation. Same-day service, fully insured, all hardware included.

Call (213) 556-4558

Method 4: Tap Testing

No Tools Needed Takes Practice

Knock on the wall with your knuckles and listen carefully. Over hollow drywall you'll hear a hollow, resonant sound. Over a stud, the sound is denser, a duller, lower-pitched knock with less resonance. The sound difference is subtle, but most people can learn to distinguish it in a few minutes of practice on the same wall.

This works best as a rough location method, then confirm with a magnet or stud finder before drilling. Don't rely on tap testing alone for a TV mount, but it's useful for narrowing your search area before scanning.

Method 5: Baseboard and Crown Molding Nails

No Scanning Required Floor-Level Only

Baseboards are nailed into studs at the bottom of walls. Look at the baseboard along the wall where you plan to mount, you'll often see small nail holes, dimples, or putty spots where finish nails were driven. Each nail cluster marks a stud location. Use a straight edge to project a vertical line up the wall to your mounting height.

Crown molding at ceiling height uses the same principle. If you can see the nail holes in crown molding, you have another set of stud reference points that can be measured down to your mounting height.

What If Studs Aren't Where You Need Them?

It's common to find that studs don't align with your ideal TV position. You have two good options:

Stud Spacing: 16" vs 24": How to Tell

Most US homes built after 1965 use 16" on-center stud spacing. Homes built in the 1950s–1960s, and most commercial construction, often used 24" OC spacing. To determine which you have:

  1. Find one confirmed stud using any method above
  2. Measure 16" in one direction and check for another stud
  3. If nothing is there at 16", measure 24" from your first stud
  4. Whichever spacing confirms, use that for all subsequent measurements along that wall

Metal-framed walls (common in condos, commercial buildings, and newer multifamily construction) also use 16" or 24" spacing, but the studs are lighter gauge and have lower holding strength than wood. TV mounts in metal-stud walls should use 2 studs minimum and appropriate metal-thread screws, never standard wood screws in metal studs.

Important: Always scan for electrical wires and plumbing before drilling, especially in exterior walls and near outlets. Use a stud finder with AC wire detection (Franklin T6, Zircon i520) or a dedicated wire scanner. Drilling into live electrical wires causes serious injury and significant repair costs.

Professional Installation: Studs Located, No Guesswork

TV Mount Experts handles stud location, wire avoidance, and bracket alignment as part of every installation. Starting at $55 for standard drywall mounting.

Get a Quote

Frequently Asked Questions

How far apart are studs in a wall?

In standard US residential construction, studs are spaced 16 inches on center (OC). Some homes, particularly those built in the 1950s–1970s, used 24-inch OC spacing. The spacing is measured from the center of one stud to the center of the next, not edge to edge. This means if you find one stud, the next is 16 or 24 inches away from it.

Why is my stud finder giving wrong readings?

The most common reasons a stud finder fails: (1) Dead or low battery, replace it first. (2) Calibrating on top of a stud, always start the scan 6 inches from where you think a stud might be. (3) Lath-and-plaster walls, magnetic stud finders work better than electronic ones on plaster. (4) Metal conduit or pipes, will trigger a stud finder falsely. Confirm any stud detection by probing with a thin finish nail before drilling.

Can you find a stud without a stud finder?

Yes. The most reliable no-tool method: locate an electrical outlet on the wall, by code, the stud box attaches to the side of a stud, so the stud is 3/4 inch (the thickness of the box nailing flange) from the box edge. From there, measure 16 inches toward your desired mounting location. You can also use a rare-earth magnet to find the drywall screws that attach to the stud, drywall screws are typically 12 inches apart vertically, so you'll feel a cluster of magnetic pulls in a vertical line.

What is a stud in a wall, and why does it matter for TV mounting?

A stud is a vertical wooden (or metal) framing member inside the wall, typically 2×4 or 2×6 lumber. Studs are the structural support of the wall, they run from floor plate to ceiling plate. For TV mounting, you need to drive screws into studs because drywall alone cannot reliably support a TV's weight without special anchors. A screw into a stud has roughly 10x the pull-out strength of a screw into plain drywall.